Faucet Repair Service
Call Now (855) 557-9600
Faucet repair stops persistent drips that waste over 3,000 gallons per year according to USGS estimates, rebuilds cartridges and ceramic discs that cause erratic temperature mixing, and replaces worn O-rings and valve seats before staining and finish erosion worsen. Bonded Plumbworks’ licensed plumbers diagnose the internal component failure — cartridge, stem, or ball valve — and install manufacturer-specified replacement parts to restore full function without swapping the entire fixture.
What Is Faucet Repair
Faucet repair is the process of diagnosing and fixing a malfunctioning faucet without replacing the entire unit. Most faucet failures originate from worn internal components — cartridges, O-rings, valve seats, ceramic discs, springs, and diverters. The repair approach depends on the faucet type. The four primary faucet mechanisms are compression (washer-based), ball (spring-loaded rotating ball), cartridge (single or dual cartridge), and ceramic disc (paired ceramic plates). Each type has distinct failure modes and requires specific replacement parts.
The Plumbing-Heating-Cooling Contractors Association (PHCC) recommends professional repair over DIY attempts for cartridge and ceramic disc faucets, where improper disassembly can crack the valve body or damage the cartridge housing — turning a repair into a full replacement.
When to Schedule Faucet Repair
A steady drip from the spout when the handle is fully closed indicates a worn cartridge, seat, or washer. Water leaking from beneath the handle points to a failed O-ring or packing nut. Difficulty turning the handle suggests mineral buildup inside the valve body — a common issue where water hardness averages 150 to 250 parts per million (PPM). Reduced flow from the spout may indicate a clogged aerator, but if cleaning the aerator does not restore flow, internal valve obstruction is likely.
A faucet that does not maintain a consistent temperature when you adjust the handle indicates cartridge wear in single-handle mixing faucets. A loose or wobbling handle often indicates a stripped handle set screw — this small fastener secures the handle to the valve stem, and when it fails, the handle spins without engaging the cartridge, making faucet repair impossible until the screw is replaced or re-seated. Water pooling at the base of the faucet suggests a failed base seal or O-ring. Any of these symptoms warrant professional diagnosis before the problem escalates to supply line damage or countertop water intrusion.
How It Works
Diagnosis
Our plumber identifies the faucet manufacturer and model, determines the mechanism type, and tests operation to isolate the failed component. We shut off the water supply at the fixture shut-off valves and relieve residual pressure before disassembly. Faucet Repair inspection gives you a live view of the problem before any work starts. You review the findings and approve the quote before any repair begins.
Disassembly and Component Inspection
We remove the handle, escutcheon, and internal cartridge or valve assembly. The escutcheon plate — the decorative trim ring between the faucet body and the wall or countertop surface — is inspected for corrosion and proper seal during faucet repair, because a damaged escutcheon allows water to seep behind the mounting surface and cause hidden moisture damage. Each component is inspected for wear, corrosion, and mineral deposits. We examine the valve seat for pitting or scoring — a damaged seat will destroy a new cartridge or washer within weeks if not resurfaced or replaced.
Repair and Reassembly
Failed components are replaced with manufacturer-specified parts. We use genuine Moen cartridges for Moen faucets, genuine Delta ball assemblies and springs for Delta faucets, and OEM-equivalent parts from Danco or BrassCraft where originals are discontinued. All O-rings and seals are replaced during the repair regardless of apparent condition — they are inexpensive insurance against a callback. We apply food-grade silicone plumber’s grease to all moving surfaces before reassembly.
Testing
We restore water supply and test the faucet through full range of motion — cold, hot, mixed, and off. We check for drips at every position, verify handle smoothness, and inspect all connection points under pressure for leaks.
Benefits vs Alternatives
Faucet repair preserves a functioning fixture at a fraction of the replacement cost. A cartridge replacement typically costs $150 to $300, while a new faucet installation runs $300 to $700 or more depending on the fixture. Repair also avoids the countertop or sink modifications that some replacement faucets require when mounting hole configurations differ.
However, repair is not always the best option. If the valve body is corroded, the finish is deteriorating, or the faucet is more than 15 years old, replacement provides better long-term value. Smart leak detection placed under the sink cabinet alerts homeowners to slow drips from faucet supply connections that would otherwise go unnoticed until water damage develops, complementing faucet repair by monitoring the connections most likely to fail after service. Faucets manufactured before 2014 may not meet current WaterSense standards set by the Environmental Protection Agency (EPA), and upgrading to a compliant model (1.5 GPM maximum at 60 PSI) reduces water consumption by up to 30 percent compared to older designs.
Pricing
Faucet repair typically ranges from $125 to $350 depending on the faucet type and the components that need replacement. Simple washer or O-ring replacements fall at the lower end. Cartridge replacements for single-handle kitchen faucets with pull-down sprayers or touchless sensors are at the higher end due to part cost and labor complexity. Bonded Plumbworks provides a written estimate before beginning any repair.
Qualifications
Bonded Plumbworks plumbers hold active state plumbing licenses and carry manufacturer-specific training on Moen, Delta, Kohler, and American Standard faucet lines. Smart faucet sensor repair for touchless kitchen and bathroom faucets requires specialized diagnostic knowledge of infrared proximity sensors, solenoid valves, and battery or AC power systems that differ from traditional faucet repair methods. We have been repairing faucets since 2006 and maintain an A+ rating with the Better Business Bureau (BBB). We are members of the Plumbing-Heating-Cooling Contractors Association (PHCC).
Frequently Asked Questions
How much does faucet repair cost?
Faucet Repair typically costs $125 to $350 for most residential jobs. The final price depends on the scope of work, materials required, and site conditions. Bonded Plumbworks provides a written estimate before starting any faucet repair work, so you know the exact cost upfront. Call (855) 557-9600 for a same-day quote.
Is it worth repairing an old faucet or should I replace it?
If the faucet is less than 10 to 12 years old and the valve body is in good condition, repair is usually the most cost-effective choice. For faucets older than 15 years, especially those with visible corrosion or finish deterioration, replacement provides better value and brings the fixture up to current WaterSense efficiency standards.
Can you repair any brand of faucet?
We repair all major faucet brands including Moen, Delta, Kohler, American Standard, Grohe, Pfister, and TOTO. For less common brands, we source compatible replacement parts from Danco and BrassCraft, which manufacture aftermarket cartridges and repair kits for most residential faucets.
Why does my faucet drip after I already had it repaired?
Recurring drips after repair usually indicate a damaged valve seat that was not addressed during the initial repair, or a replacement cartridge that does not match the original specifications. Bonded Plumbworks’ technicians always inspect and resurface or replace the valve seat during cartridge repairs to prevent this issue.
Back to Faucet Fixture Services
Schedule Today
Call Bonded Plumbworks at (855) 557-9600 to schedule faucet repair. Our licensed plumbers diagnose and fix dripping, leaking, and malfunctioning faucets — often on the same day you call. Every faucet repair service includes a 90-day guarantee on faucet repair work, covering parts and labor.